|
|
| Product
|
Description
|
Price
|
|
2017-2020 Suzuki GSX-S 1000 Race Tools Package
The Race Tools package allows you to enable Quickshifter, Launch Control and Pit Speed Limiter in the Stock ECU. The package includes: - High quality strain gauge Quickshifter with digitally controlled pressure sensing that can be used in regular or race shift pattern.
- Shift rod for standard shift configuration*
- Suzuki Race Tools Harness Type 5 which allows the quickshifter to be plugged into the bikes wiring harness**
- Race Tools Key to allow the use of the Race Tools on one ECU in the Woolich Racing Tuned software.
Quickshifter Kill times are configurable per gear with 3D maps allowing Kill Times to be set for the full range of TPS and RPM combinations. The quickshifter kills both fuel and ignition. Launch Control allows you to configure Delay, Launch RPM, Ramp Time and Ramp RPM Pit Speed Limiter allows you to set the RPM to limit the speed while riding through the pits.*** * Contact us after ordering if you have after-market rearsets or are using a race shift pattern and we will swap the shift rod for a generic rod that can be cut and tapped to the correct length. ** This harness uses the stock Exhaust Valve plugs on the bike's harness, the stock Exhaust Valve should be removed from the bike and disabled in our software *** Pit Speed Limiter harness sold separately
Woolich Racing Race Tools requires you to Write the ECU. It is not a stand alone product. You will need to use the relevant Woolich Racing Interface and Bin File Definition to enable and configure Race Tools and write to the ECU. You can purchase this as a package on the product page for your bike. If you do not have a Woolich Racing Interface you can also visit a Woolich Racing - Tuning Partner and have them install and configure the Race Tools (additional fees and charges will apply).
|
Pit Speed Limiter Harness
The Pit Speed Limiter harness is used with our Race Tools Package, it consists of a harness and water proof push button switch which allows you to limit the RPM of the bike in 1st gear while riding in the pits. You must have a Race Tool Package to use the Pit Speed Limiter Harness.
The Pit Speed Limiter harness also includes a stainless steel bracket used to mount the button on the bike's switch gear.
Woolich Racing Race Tools requires you to Write the ECU. It is not a stand alone product. You will need to use the relevant Woolich Racing Interface and Bin File Definition to enable and configure Race Tools and write to the ECU. You can purchase this as a package on the product page for your bike. If you do not have a Woolich Racing Interface you can also visit a Woolich Racing - Tuning Partner and have them install and configure the Race Tools (additional fees and charges will apply).
|
|
|
|
|
Bin File Definitions - for use in Woolich Racing Tuned software
|
|
Product
|
Description
|
Price
|
|
2017-2020 GSX-S 1000 Stock Bin File Definitions
Purchase this item to gain access in the Woolich Racing Tuned software to the bin file definitions for the 2017-2020 GSX-S 1000
Note: The WRT software is only available to verified
Woolich accounts. We only verify customer accounts that have purchased
the necessary products (Woolich Log Box or USB interface, along with the
appropriate harness and -if required- a bin file definition key) to
flash their ECU. Accounts with no purchases of the required products can
not be verified.
AU$
110.00
Features available for Suzuki GSX-S 1000 2017-2020 - IAP Fuel Maps
- TPS Fuel Maps
- Ignition Timing Maps
- Ignition Dwell Map/s
- Secondary Throttle Plate (STP) Opening Maps
- Fuel Trim Map/s
- Exhaust Valve Opening Maps
- RPM Limiter
- Fan Temperature
- Quickshifter - (Requires Race Tools)
- Launch Control - (Requires Race Tools)
- Pit Lane Limiter - (Requires Race Tools)
- Race Shift Pattern Sensor Configuration - (Requires Race Tools)
- Disable Evap / Purge Valve
- Disable Stock O2 Sensor
- Disable Deceleration Fuel Cut
- Disable Exhaust Valve
- Disable PAIR Valve / AIS
- Disable Top Speed Limiter
- Engine Data - View Live Engine Data
- Woolich Racing AutoTune - (Requires Applicable LogBox + Zeitronix Package)
- Diagnostics: Read and Clear Fault Codes - (Requires Applicable V3 Interface)
ECU Part Numbers: - 32920-38K30
- 32920-38K31
- 32920-38K40
- 32920-38K50
- 32920-38K51
- 32920-38K90
- 32920-38KB0
- 32920-38KD0
- 32920-38KE0
This product comes with 1 Bin File Definition Key allowing you to tune 1 ECU's as many times as you like. Additional Bin File Definition Keys are required for each additional ECU's and can be purchased from within the WRT software.
|
|
|
Harnesses
|
|
Product
|
Description
|
Price
|
|
Extension Harness Long
The Extension Harness - Long is a 8 pin Molex (male) to 8 Pin Molex (female) entension harness 1100mm long that allows you to extend the length of all Woolich Racing Harnesses.
|
Extension Harness Short
The Extension Harness - Short is a 8 pin Molex (male) to 8 Pin Molex (female) extension harness 600mm long that allows you to extend the length of all Woolich Racing Harnesses.
|
Suzuki Dealer Mode Harness Type 1
The Suzuki Dealer Mode Harness plugs into the bikes diagnostic plug. When you turn the ignition on with the harness installed you will be able to see fault codes and access dealer menu's on the dash. The features available vary with model.
Compatible with the following models:
Suzuki C109 Boulevard/C109 Intruder 2008-2011 Suzuki C90 Boulevard/VL 1500 Intruder 2005-2015 Suzuki GSF 1250 (Bandit) 2007-2016 Suzuki GSF 650 (Bandit) 2008-2012 Suzuki GSR 400 2006-2009 Suzuki GSR 600 2006-2010 Suzuki GSR 750 2011-2017 Suzuki GSX 1400 2004-2008 Suzuki GSX1300BK (B-King)2007-2012 Suzuki GSX1300R (Hayabusa)2008-2020 Suzuki GSX-R 1000 2003-2024 Suzuki GSX-R 1000 EM-Pro Race Kit ECU 2020 Suzuki GSX-R 1000R 2017-2024 Suzuki GSX-R 600 2004-2024 Suzuki GSX-R 750 2004-2024 Suzuki GSX-S 1000 2015-2020 Suzuki GSX-S 1000 Katana 2019-2020 Suzuki GSX-S 750 2015 2020 Suzuki M109R 2006-2020 Suzuki SFV 650 SV 650S (Gladius)2009-2015 Suzuki SV 1000 2005-2008 Suzuki SV 650 2007-2012
|
12V Bench Flashing Power Supply with Type A Plug (USA, Canada, Japan)
This 12V, 1.5A Power Supply (max output 13V) has been designed for use with Woolich Racing Bench Harnesses.
This product comes with an integrated on/off switch and interchangeable Type A plug used in USA, Canada, Japan and Mexico.
Input: 100-240V 50/60Hz *This power supply is NOT designed to be used as a battery charger.
|
12V Bench Flashing Power Supply with Type C plug (Europe, Asia)
This 12V, 1.5A Power Supply (max output 13V) has been designed for use with Woolich Racing Bench Harnesses.
This product comes with an integrated on/off switch and interchangeable Type C plug used in most of Europe, parts of Asia, and parts of South America.
Input: 100-240V 50/60Hz *This power supply is NOT designed to be used as a battery charger.
|
12V Bench Flashing Power Supply with Type I plug (AU, NZ, China)
This 12V, 1.5A Power Supply (max output 13V) has been designed for use with Woolich Racing Bench Harnesses.
This product comes with an integrated on/off switch and interchangeable Type I plug used in Australia, New Zealand and mainland China.
Input: 100-240V 50/60Hz *This power supply is NOT designed to be used as a battery charger.
|
12V Bench Flashing Power Supply with Type G plug (UK, Malaysia & Singapore)
This 12V, 1.5A Power Supply (max output 13V) has been designed for use with Woolich Racing Bench Harnesses. This product comes with an integrated on/off switch and interchangeable Type G plug used in the UK, Ireland, Malaysia & Singapore. Input: 100-240V 50/60Hz *This power supply is NOT designed to be used as a battery charger.
|
Suzuki O2 Eliminator Type 1
The Woolich Racing O2 Eliminator allows you to remove the O2 Sensor/s from the motorcycle. The eliminator prevents the bike from displaying the Malfunction Indicator Light (MIL) on the dash and prevents fault codes from appearing in the diagnostic system.
The eliminator should be plugged into the bikes wiring harness before the ignition is switched back on to prevent fault codes from being stored in the ECU.
Supported models: - SV650 2007-2014 - VStrom 650 2012+ - GSX-R 750 2008 - GSX-R 600 2008 - GSX-R 1000 2007+ - GSX-S 1000 2016+
|
|
|
Motorcycle Diagnostics - OBD2
|
|
Product
|
Description
|
Price
|
|
OBD2 Diagnostic Scanner (Advanced)
The OBD2 Diagnostic Scanner - Advanced allows you to read and clear fault codes when used in conjunction with the relevant Woolich Racing OBD2 Harness suitable to your bike.
Please note that not all OBD2 Diagnostic Scanners work on Motorcycles. This particular device has been tested by Woolich Racing and it works on the motorcycles where it is listed as a product.
|
Suzuki Dealer Mode Harness Type 1
The Suzuki Dealer Mode Harness plugs into the bikes diagnostic plug. When you turn the ignition on with the harness installed you will be able to see fault codes and access dealer menu's on the dash. The features available vary with model.
Compatible with the following models:
Suzuki C109 Boulevard/C109 Intruder 2008-2011 Suzuki C90 Boulevard/VL 1500 Intruder 2005-2015 Suzuki GSF 1250 (Bandit) 2007-2016 Suzuki GSF 650 (Bandit) 2008-2012 Suzuki GSR 400 2006-2009 Suzuki GSR 600 2006-2010 Suzuki GSR 750 2011-2017 Suzuki GSX 1400 2004-2008 Suzuki GSX1300BK (B-King)2007-2012 Suzuki GSX1300R (Hayabusa)2008-2020 Suzuki GSX-R 1000 2003-2024 Suzuki GSX-R 1000 EM-Pro Race Kit ECU 2020 Suzuki GSX-R 1000R 2017-2024 Suzuki GSX-R 600 2004-2024 Suzuki GSX-R 750 2004-2024 Suzuki GSX-S 1000 2015-2020 Suzuki GSX-S 1000 Katana 2019-2020 Suzuki GSX-S 750 2015 2020 Suzuki M109R 2006-2020 Suzuki SFV 650 SV 650S (Gladius)2009-2015 Suzuki SV 1000 2005-2008 Suzuki SV 650 2007-2012
|
Suzuki OBD2 Harness Type 1
This OBD2 harness allows you to connect to the 6 Pin SDS Diagnostic Plug on the bike and read and clear fault codes using a OBD2 Diagnostic Scanner.
This product is for customers who do not have access to one of our Interfaces but needs to read and clear fault codes. This product is not required if you already have a Woolich Racing Interface and On Bike Harness as we have diagnostics built into the software.
Note: OBD2 Diagnostic Scanner is not included, please see our listings for OBD2 Diagnostic Scanners that we have tested and work for this application.
Compatible with the following models: Suzuki GSX-R 1000 2017-2023 Suzuki GSX-R 1000R 2017-2023 Suzuki GSX-S 1000 2017-2019 Suzuki GSX-S 1000 Katana 2019-2020 Suzuki SV 650 2017-2020
|
OBD2 Diagnostic Scanner (Basic)
The OBD2 Diagnostic Scanner - Basic allows you to read and clear fault codes when used in conjunction with the relevant Woolich Racing OBD2 Harness suitable to your bike.
Please note that not all OBD2 Diagnostic Scanners work on Motorcycles. This particular device has been tested by Woolich Racing and it works on the motorcycles where it is listed as a product.
|
|
| Woolich Racing Merchandise |
|
Product
|
Description
|
Price
|
|
Woolich Racing Keytag
Woolich Racing embroidered keytag - easy to retrieve your keys even with bike gloves on!
|
|
| Wideband O2 Products |
|
Product
|
Description
|
Price
|
|
Zeitronix ZT-3 Wideband O2 Kit
Includes - Zeitronix ZT-3 Wideband O2 Controller
- 3 foot O2 sensor harness
- Extended primary O2 sensor harness (easier to fit to motorcycles)
|
Ducati Wideband O2 Installation Kit (Zeitronix) (type 3)
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 to a Ducati V2 motorcycle Includes: - 2 x Wideband O2 sensor bung
- 2 x 12v Automotive Relay
- 2 of each Red and Black 1.5mm Automotive Wire
- 8 * push on terminals
- 4 * 6mm eye connectors
- Heatshrink
- 2 x Wiretap
- RJ12 cable for connecting ZT-3 to Woolich Racing Products
- 2 x Adhesive Velcro for attaching ZT-3
|
Ducati Wideband O2 Installation Kit (Zeitronix) Type 1 (Stainless Steel)
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 to relevant Ducati models (Stainless Steel Bungs) Includes: - Twin RJ12 cable to connect Zeitronix to Log Box
- Short O2 sensor harness to ZT3
- Ducati Power Harness 1 & 2
- x O2 Stainless Steel Bung
- Adhesive Velcro for attaching ZT-3 to bike.
|
Ducati Wideband O2 Installation Kit (Zeitronix) Type 1 (Titanium)
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 to relevant Ducati models (TITANIUM Bungs)
Includes: - Twin RJ12 cable to connect Zeitronix to Log Box
- Short O2 sensor harness to ZT3
- Ducati Power Harness 1 & 2
- 2 x O2 TITANIUM Bungs
- Adhesive Velcro for attaching ZT-3 to bike.
|
Ducati Wideband O2 Installation Kit (Zeitronix) Type 2
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 to relevant Ducati models
Includes: - RJ12 cable for connecting ZT-3 to Woolich Racing Products
- Ducati Wideband Power Harness Type 3
- 1 x O2 Stainless Steel Bung
- Adhesive Velcro for attaching ZT-3 to bike.
|
Honda Wideband O2 Installation Kit (Zeitronix ZT3)
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 Kit to relevant Honda models.
Includes: - RJ12 cable for connecting ZT-3 to Woolich Racing Products
- Honda Wideband Power Harness Type 1
- 1 x O2 Stainless Steel Bung
- Adhesive Velcro for attaching ZT-3 to bike.
|
Kawasaki Wideband O2 Installation Kit (Zeitronix) (Type 1)
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 to relevant Kawasaki models
Includes: - RJ12 cable for connecting ZT-3 to Woolich Racing Products
- Kawasaki Power Harness Type 1
- O2 Stainless Steel Bung
- Adhesive Velcro for attaching ZT-3 to bike.
|
Kawasaki Wideband O2 Installation Kit (Zeitronix) (Type 2)
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 to relevant Kawasaki models
Includes: - RJ12 cable for connecting ZT-3 to Woolich Racing Products
- Kawasaki Power Harnes Type 2
- O2 Stainless Steel Bung
- Adhesive Velcro for attaching ZT-3 to bike.
|
KTM Wideband O2 Installation Kit (Zeitronix ZT4)
Installation kit for fitting the Zeitronix ZT-4 Dual Wideband O2 Kit to relevant KTM models
Includes: - RJ12 cables for connecting ZT-3 to Woolich Racing Products
- KTM Power Harness Type 1
- 2 x O2 Stainless Steel Bung
- Adhesive Velcro for attaching ZT-4 to bike.
|
Suzuki Wideband O2 Installation Kit (Zeitronix)
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 to relevant Suzuki models
Includes: - RJ12 cable for connecting ZT-3 to Woolich Racing Products
- Suzuki Power Harness
- O2 Stainless Steel Bung
- Adhesive Velcro for attaching ZT-3 to bike.
|
Woolich Racing Tuning Shop Zeitronix Installation Kit
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 to a motorcycle Includes: - Wideband O2 sensor bung (stainless Steel)
- Wideband O2 sensor bung (Titanium)
- Tuning Shop Power Harness (type 1)
- RJ12 cables for connecting ZT-3 to Woolich Racing Products - 1 x small, 1 x large
- 2 x Narrow band bungs
|
Woolich Racing Zeitronix Installation Kit
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 to a motorcycle Includes: - Wideband O2 sensor bung
- 12v Automotive Relay
- Red and Black 1.5mm Automotive Wire
- 4 * push on terminals
- 2 * 6mm eye connectors
- Heatshrink
- Wiretap
- RJ12 cable for connecting ZT-3 to Woolich Racing Products
- Adhesive Velcro for attaching ZT-3 to bike.
|
Woolich Racing Zeitronix Installation Kit ZT-3 OBD2
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 for motorcycles that use the red OBD plug. Includes: - Wideband O2 sensor bung
- OBD2 Wideband Harness Type 1
- RJ12 cable for connecting ZT-3 to Woolich Racing Products
- Adhesive Velcro for attaching ZT-3 to bike.
|
Woolich Racing Zeitronix Installation Kit ZT-4 OBD2
Installation kit for fitting the Zeitronix ZT-4 Wideband O2 for motorcycles that use the red OBD plug. Includes: - Wideband O2 sensor bung
- OBD2 Wideband Harness Type 2
- RJ12 cable for connecting ZT-4 to Woolich Racing Products
- Adhesive Velcro for attaching ZT-4 to bike.
|
Woolich Racing Zeitronix Installation Kit (ZT-4)
Installation kit for fitting the Zeitronix ZT-4 Dual Wideband O2 to a motorcycle Includes: - 2 x Wideband O2 sensor bungs
- Wideband Harness (to connect battery terminal for power)
- RJ12 cable for connecting ZT-4 to Woolich Racing Products
- Adhesive Velcro for attaching ZT-4 to bike.
|
Yamaha Wideband O2 Installation Kit (Zeitronix)
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 to relevant Yamaha models
Includes: - RJ12 cable for connecting ZT-3 to Woolich Racing Products
- Yamaha Power Harness
- O2 Stainless Steel Bung
- Adhesive Velcro for attaching ZT-3 to bike.
|
Zeitronix ZT-4 Dual Wideband O2 Kit
Zeitronix ZT-4 Dual Wideband O2 Controller Kit, with 2 x Zeitronix Wideband O2 Sensor (3 foot cable)
Woolich Racing - Tuning Shop Zeitronix Power Harness Type 3 1 x RJ12 Cable
|
Stainless Steel Wideband O2 Bung
High Quality 18mm Stainless Steel Wideband O2 Bung. You can weld this bung into exhaust systems that do not have a Wideband O2 bung.
|
Titanium Wideband O2 Bung
High Quality 18mm Titanium Wideband O2 Bung. You can weld this bung into exhaust systems that do not have a Wideband O2 bung.
|
Wideband Bung Bolt
The Stainless Steel Wideband Bung Bolt allows you to block off a Wideband O2 bung when the Wideband O2 sensor is not installed.
|
Wideband Bung Bolt Race
The Stainless Steel Wideband Bung Bolt allows you to block off a Wideband O2 bung when the Wideband O2 sensor is not installed. This Race version of the bung bolt is light weight and has holes pre-drilled for lock wiring.
|
Narrowband Bung Bolt
The Stainless Steel 12mm Narrowband Bung Bolt allows you to block off a Narrowband O2 bung allowing the Narrowband sensor to be entirely removed from the bike.
|
Narrowband to Wideband O2 Adapter
The Narrowband to Wideband O2 sensor adapter screws into a 12mm Narrowband bung, allowing you to use a Wideband O2 sensor with a Narrowband bung.
Please Note: This is a generic item and may not fit all makes/models due to potential clearance issues that arise from the manufacturers' designs. Please ensure you have adequate clearance for the adapter -AND- the O2 sensor when installed in the factory narrowband location.
- O2 Adapter Height: Approximately 32 mm extending vertically when installed in the stock narrowband location. - O2 Sensor Height: Plan for at least 70 mm of additional height on top of the O2 Adapter when the wideband O2 sensor is installed.
For models where clearance could be an issue, it is suggested to use the wideband bung included in the Zeitronix installation kit or find an alternative narrowband to wideband adapter such as the Innovate 12mm to 18mm O2 BUNG ADAPTER, P/N 38350 which angles the sensor to help potentially alleviate any clearance issues.
|
Zeitronix ZR-1 AFR Gauge Blue LED
- Stylish, machined, anodized black bezel and slim enclosure
- High contrast Blue LED display
- Large 0.4" (10mm) digits
- Slim design for flexible gauge mounting options
- Programmable to startup as an AFR or Lambda gauge
- Peak and Hold feature
- RJ12 Splitter cable included
|
Zeitronix ZR-1 AFR Gauge Red LED
- Stylish, machined, anodized black bezel and slim enclosure
- High contrast Red LED display
- Large 0.4" (10mm) digits
- Slim design for flexible gauge mounting options
- Programmable to startup as an AFR or Lambda gauge
- Peak and Hold feature
- RJ12 Splitter cable included
|
Zeitronix ZR-3 AFR Gauge Blue LED
- Blue digital AFR readout with large 0.4" (10mm) digits
- Slim 0.75" (19mm) design
- High contrast display visible even in direct sunlight
- RJ12 Splitter cable included
|
Zeitronix ZR-3 AFR Gauge Red LED
- Red digital AFR readout with large 0.4" (10mm) digits
- Slim 0.75" (19mm) design
- High contrast display visible even in direct sunlight
- RJ12 Splitter cable included
|
Hacker/Tweaker AFR Display Blue LED
The Zeitronix Hacker/Tweaker is a very small AFR or Lambda display for the Zt-3 Wideband Systems. Designed to fit into tight spots, full board dimensions are less than 2" by 1". Like all LED displays it requires a tinted foil or Lexan cover. There are two mounting holes for screws or standoffs. It powers up right from the Zt-3 DATA port. RJ12 splitter cable included.
Note: The Hacker/Tweaker is a bare PCB board, you will need to make your own case.
|
Hacker/Tweaker AFR Display Red LED
The Zeitronix Hacker/Tweaker is a very small AFR or Lambda display for the Zt-3 Wideband Systems. Designed to fit into tight spots, full board dimensions are less than 2" by 1". Like all LED displays it requires a tinted foil or Lexan cover. There are two mounting holes for screws or standoffs. It powers up right from the Zt-3 DATA port. RJ12 splitter cable included.
Note: The Hacker/Tweaker is a bare PCB board, you will need to make your own case.
|
|
| |
|
|
|
|