|
|
| Product
|
Description
|
Price
|
|
2007-2008 Yamaha YZF-R1 Race Tools
The Race Tools package allows you to add Autoblipper, Quickshifter, Pit Speed Limiter, Engine Warm Up and Launch Control to the Stock R1 ECU. The package includes: - High quality dual direction strain gauge Quickshifter with digitally controlled pressure sensing that can be used in regular or race shift pattern.
- Shift rod for standard shift configuration*
- Yamaha Race Tools Type 1 which allows the quickshifter to be plugged into the bikes wiring harness**
- Race Tools Key to allow the use of the Race Tools on one ECU in the Woolich Racing Tuned software.
Quickshifter Kill times are configurable per gear with 3D maps allowing Kill Times to be set for the full range of TPS and RPM combinations. Autoblipper Opening and Duration maps are fully configurable per gear. Launch Control allows you to configure Delay, Launch RPM and Hold Speed. Pit Speed Limiter RPM can be configured.*** Engine Warm Up parameters are configurable.*** * Contact us after ordering if you have after-market rearsets or are using a race shift pattern and we will swap the shift rod for a generic rod that can be cut and tapped to the correct length. ** This harness uses the stock exhaust valve plugs on the bike's harness, the stock exhaust valve should be removed from the bike and disabled in the WRT software *** The Pit Speed Limiter / Engine Warm Up requires the purchase of an additional Pit Speed Limiter harness
Woolich Racing Race Tools requires you to Write the ECU. It is not a stand alone product. You will need to use the relevant Woolich Racing Interface and Bin File Definition to enable and configure Race Tools and write to the ECU. You can purchase this as a package on the product page for your bike. If you do not have a Woolich Racing Interface you can also visit a Woolich Racing - Tuning Partner and have them install and configure the Race Tools (additional fees and charges will apply).
|
2017-2019 YZF-R1 Pit Speed Limiter
This product includes the Yamaha Race Tools Harness Type 1, Pit Speed Limiter Harness and Pit Speed Limiter Key allowing you to enable the Pit Speed Limiter in 1 ECU within the Woolich Racing Tuned (WRT) software..
Woolich Racing Race Tools requires you to Write the ECU. It is not a stand alone product. You will need to use the relevant Woolich Racing Interface and Bin File Definition to enable and configure Race Tools and write to the ECU. You can purchase this as a package on the product page for your bike. If you do not have a Woolich Racing Interface you can also visit a Woolich Racing - Tuning Partner and have them install and configure the Race Tools (additional fees and charges will apply).
|
2009-2011 Yamaha YZF-R1 Race Tools
The Race Tools package allows you to add Autoblipper, Quickshifter, Pit Speed Limiter, Engine Warm Up and Launch Control to the Stock R1 ECU. The package includes: - High quality dual direction strain gauge Quickshifter with digitally controlled pressure sensing that can be used in regular or race shift pattern.
- Shift rod for standard shift configuration*
- Yamaha Race Tools Type 2 which allows the quickshifter to be plugged into the bikes wiring harness**
- Race Tools Key to allow the use of the Race Tools on one ECU in the Woolich Racing Tuned software.
Quickshifter Kill times are configurable per gear with 3D maps allowing Kill Times to be set for the full range of TPS and RPM combinations. Autoblipper Opening and Duration maps are fully configurable per gear. Launch Control allows you to configure Delay, Launch RPM and Hold Speed. Pit Speed Limiter RPM can be configured.*** Engine Warm Up parameters are configurable.*** * Contact us after ordering if you have after-market rearsets or are using a race shift pattern and we will swap the shift rod for a generic rod that can be cut and tapped to the correct length. ** This harness uses the O2 sensor plugs on the bike's harness, the stock O2 sensor should be removed from the bike and disabled in the WRT software *** The Pit Speed Limiter / Engine Warm Up requires the purchase of an additional Pit Speed Limiter harness
Woolich Racing Race Tools requires you to Write the ECU. It is not a stand alone product. You will need to use the relevant Woolich Racing Interface and Bin File Definition to enable and configure Race Tools and write to the ECU. You can purchase this as a package on the product page for your bike. If you do not have a Woolich Racing Interface you can also visit a Woolich Racing - Tuning Partner and have them install and configure the Race Tools (additional fees and charges will apply).
|
2012-2014 Yamaha YZF-R1 Race Tools
The Race Tools package allows you to add Autoblipper, Quickshifter, Pit Speed Limiter, Engine Warm Up and Launch Control to the Stock R1 ECU. The package includes: - High quality dual direction strain gauge Quickshifter with digitally controlled pressure sensing that can be used in regular or race shift pattern.
- Shift rod for standard shift configuration*
- Yamaha Race Tools Type 2 which allows the quickshifter to be plugged into the bikes wiring harness**
- Race Tools Key to allow the use of the Race Tools on one ECU in the Woolich Racing Tuned software.
Quickshifter Kill times are configurable per gear with 3D maps allowing Kill Times to be set for the full range of TPS and RPM combinations. Autoblipper Opening and Duration maps are fully configurable per gear. Launch Control allows you to configure Delay, Launch RPM and Hold Speed. Pit Speed Limiter RPM can be configured.*** Engine Warm Up parameters are configurable.*** * Contact us after ordering if you have after-market rearsets or are using a race shift pattern and we will swap the shift rod for a generic rod that can be cut and tapped to the correct length. ** This harness uses the O2 sensor plugs on the bike's harness, the stock O2 sensor should be removed from the bike and disabled in the WRT software *** The Pit Speed Limiter / Engine Warm Up requires the purchase of an additional Pit Speed Limiter harness
Woolich Racing Race Tools requires you to Write the ECU. It is not a stand alone product. You will need to use the relevant Woolich Racing Interface and Bin File Definition to enable and configure Race Tools and write to the ECU. You can purchase this as a package on the product page for your bike. If you do not have a Woolich Racing Interface you can also visit a Woolich Racing - Tuning Partner and have them install and configure the Race Tools (additional fees and charges will apply).
|
2015-2016 Yamaha YZF-R1 Race Tools
The Race Tools package allows you to add Autoblipper, Quickshifter, Pit Speed Limiter, Engine Warm Up and Launch Control to the Stock R1 and R1M ECU. The package includes: - High quality dual direction strain gauge Quickshifter with digitally controlled pressure sensing that can be used in regular or race shift pattern.
- Shift rod for standard shift configuration*
- Yamaha Race Tools Type 1 which allows the quickshifter to be plugged into the bikes wiring harness**
- Race Tools Key to allow the use of the Race Tools on one ECU in the Woolich Racing Tuned software.
Quickshifter Kill times are configurable per gear with 3D maps allowing Kill Times to be set for the full range of TPS and RPM combinations. Autoblipper Opening and Duration maps are fully configurable per gear. Launch Control allows you to configure Delay, Launch RPM and Hold Speed. Pit Speed Limiter RPM can be configured.*** Engine Warm Up parameters are configurable.*** * Contact us after ordering if you have after-market rearsets or are using a race shift pattern and we will swap the shift rod for a generic rod that can be cut and tapped to the correct length. ** This harness uses the stock exhaust valve plugs on the bike's harness, the stock exhaust valve should be removed from the bike and disabled in the WRT software *** The Pit Speed Limiter / Engine Warm Up requires the purchase of an additional Pit Speed Limiter harness
Woolich Racing Race Tools requires you to Write the ECU. It is not a stand alone product. You will need to use the relevant Woolich Racing Interface and Bin File Definition to enable and configure Race Tools and write to the ECU. You can purchase this as a package on the product page for your bike. If you do not have a Woolich Racing Interface you can also visit a Woolich Racing - Tuning Partner and have them install and configure the Race Tools (additional fees and charges will apply).
|
2017-2019 Yamaha YZF-R1 Race Tools
The Race Tools package allows you to add Autoblipper, Quickshifter, Pit Speed Limiter, Engine Warm Up and Launch Control to the Stock R1 and R1M ECU. The package includes: - High quality dual direction strain gauge Quickshifter with digitally controlled pressure sensing that can be used in regular or race shift pattern.
- Shift rod for standard shift configuration*
- Yamaha Race Tools Type 1 which allows the quickshifter to be plugged into the bikes wiring harness**
- Race Tools Key to allow the use of the Race Tools on one ECU in the Woolich Racing Tuned software.
Quickshifter Kill times are configurable per gear with 3D maps allowing Kill Times to be set for the full range of TPS and RPM combinations. Autoblipper Opening and Duration maps are fully configurable per gear. Launch Control allows you to configure Delay, Launch RPM and Hold Speed. Pit Speed Limiter RPM can be configured.*** Engine Warm Up parameters are configurable.*** * Contact us after ordering if you have after-market rearsets or are using a race shift pattern and we will swap the shift rod for a generic rod that can be cut and tapped to the correct length. ** This harness uses the stock exhaust valve plugs on the bike's harness, the stock exhaust valve should be removed from the bike and disabled in the WRT software *** The Pit Speed Limiter / Engine Warm Up requires the purchase of an additional Pit Speed Limiter harness
Woolich Racing Race Tools requires you to Write the ECU. It is not a stand alone product. You will need to use the relevant Woolich Racing Interface and Bin File Definition to enable and configure Race Tools and write to the ECU. You can purchase this as a package on the product page for your bike. If you do not have a Woolich Racing Interface you can also visit a Woolich Racing - Tuning Partner and have them install and configure the Race Tools (additional fees and charges will apply).
|
2015-2016 Yamaha YZF-R1 Launch Control Key
Launch Control is part of the our Race Tools Package. It allows you to set a Launch RPM and other Parameters to assist with getting fast consistent launches from your bike, all controlled by the stock ECU.
If you already have a Quickshifter or Air Shifter installed on your bike or you only need the Launch Control function you can purchase this Launch Control Key. The Launch Control Key allows you to enable the Launch Control for one ECU.
If you have the full Woolich Racing Race Tools package for your bike you do not need to purchase this separate Launch Control Key.
Woolich Racing Race Tools requires you to Write the ECU. It is not a stand alone product. You will need to use the relevant Woolich Racing Interface and Bin File Definition to enable and configure Race Tools and write to the ECU. You can purchase this as a package on the product page for your bike. If you do not have a Woolich Racing Interface you can also visit a Woolich Racing - Tuning Partner and have them install and configure the Race Tools (additional fees and charges will apply).
|
2017-2019 Yamaha YZF-R1 Launch Control Key
Launch Control is part of the our Race Tools Package. It allows you to set a Launch RPM and other Parameters to assist with getting fast consistent launches from your bike, all controlled by the stock ECU.
If you already have a Quickshifter or Air Shifter installed on your bike or you only need the Launch Control function you can purchase this Launch Control Key. The Launch Control Key allows you to enable the Launch Control for one ECU.
If you have the full Woolich Racing Race Tools package for your bike you do not need to purchase this separate Launch Control Key.
Woolich Racing Race Tools requires you to Write the ECU. It is not a stand alone product. You will need to use the relevant Woolich Racing Interface and Bin File Definition to enable and configure Race Tools and write to the ECU. You can purchase this as a package on the product page for your bike. If you do not have a Woolich Racing Interface you can also visit a Woolich Racing - Tuning Partner and have them install and configure the Race Tools (additional fees and charges will apply).
|
Pit Speed Limiter Harness
The Pit Speed Limiter harness is used with our Race Tools Package, it consists of a harness and water proof push button switch which allows you to limit the RPM of the bike in 1st gear while riding in the pits. You must have a Race Tool Package to use the Pit Speed Limiter Harness.
The Pit Speed Limiter harness also includes a stainless steel bracket used to mount the button on the bike's switch gear.
Woolich Racing Race Tools requires you to Write the ECU. It is not a stand alone product. You will need to use the relevant Woolich Racing Interface and Bin File Definition to enable and configure Race Tools and write to the ECU. You can purchase this as a package on the product page for your bike. If you do not have a Woolich Racing Interface you can also visit a Woolich Racing - Tuning Partner and have them install and configure the Race Tools (additional fees and charges will apply).
|
|
|
|
|
Bin File Definitions - for use in Woolich Racing Tuned software
|
|
Product
|
Description
|
Price
|
|
|
|
|
Harnesses
|
|
Product
|
Description
|
Price
|
|
Extension Harness Long
The Extension Harness - Long is a 8 pin Molex (male) to 8 Pin Molex (female) entension harness 1100mm long that allows you to extend the length of all Woolich Racing Harnesses.
|
Extension Harness Short
The Extension Harness - Short is a 8 pin Molex (male) to 8 Pin Molex (female) extension harness 600mm long that allows you to extend the length of all Woolich Racing Harnesses.
|
Yamaha Bench Harness Type 3 (YBH3)
The bench flashing harness allows you to flash ECUs when they are not installed in the bike. The bench flashing harness comes with a 12v plug and needs to be used in conjunction with the Woolich Racing USB (Mitsubishi) Interface.
|
Yamaha Bench Harness Type 21 (YBH21)
The bench flashing harness allows you to flash 2020-2026 Yamaha YZF-R1, 2022+ MT-10 and 2021+ MT-09 ECU's on the bench. The bench flashing harness comes with a 12v plug that should be wired into a 12v power supply and needs to be used in conjunction with the Woolich Racing Log Box D-CAN Interface.
This harness should be used in conjunction with a Universal OBD2 Harness Type 1 and OBD2 Scan Tool to clear code once the ECU is back in the bike.
|
Yamaha Harness Type 7a (YH6/7/8 + YEH7a)
On Bike Harness that allows connection between Woolich Racing Log Box D-CAN v3 Interface and bike harness. Once this harness is installed it allows you to flash the ECU without pulling out the ECU. Includes: - Yamaha Harness Type 7 (Main)
- Yamaha Harness Type 7a Extension
|
Yamaha Bench Harness Type 4 (YBH4)
The bench flashing harness allows you to flash ECUs when they are not installed in the bike. The bench flashing harness comes with a 12v plug and needs to be used in conjunction with the Woolich Racing USB Interface.
|
Yamaha Bench Harness Type 5 (YBH5)
The bench flashing harness allows you to flash ECUs when they are not installed in the bike. The bench flashing harness comes with a 12v plug and needs to be used in conjunction with the Woolich Racing USB Interface.
|
Yamaha Extension Harness Type 7a (YEH7a)
The Yamaha Extension Harness Type 7a is the 4 wire extension harness that is permanently installed on the bike and connects the Yamaha Harness Type 7 main harness to the ECU. You can purchase additional Extension Harnesses to tune additional bikes.
|
12V Bench Flashing Power Supply with Type A Plug (USA, Canada, Japan)
This 12V, 1.5A Power Supply (max output 13V) has been designed for use with Woolich Racing Bench Harnesses.
This product comes with an integrated on/off switch and interchangeable Type A plug used in USA, Canada, Japan and Mexico.
Input: 100-240V 50/60Hz *This power supply is NOT designed to be used as a battery charger.
|
Yamaha Bench Harness Type 7 (YBH7)
This bench flashing harness allows you to flash ECUs when they are not installed in the bike. The bench flashing harness comes with a 12v plug and needs to be used in conjunction with the Woolich Racing Log Box D-CAN v3 Interface.
If using this product on a 2016+ bike you will need a OBD2 Harness and Code Reader to clear fault codes after writing. Woolich Racing have these available for purchase.
|
12V Bench Flashing Power Supply with Type C plug (Europe, Asia)
This 12V, 1.5A Power Supply (max output 13V) has been designed for use with Woolich Racing Bench Harnesses.
This product comes with an integrated on/off switch and interchangeable Type C plug used in most of Europe, parts of Asia, and parts of South America.
Input: 100-240V 50/60Hz *This power supply is NOT designed to be used as a battery charger.
|
12V Bench Flashing Power Supply with Type I plug (AU, NZ, China)
This 12V, 1.5A Power Supply (max output 13V) has been designed for use with Woolich Racing Bench Harnesses.
This product comes with an integrated on/off switch and interchangeable Type I plug used in Australia, New Zealand and mainland China.
Input: 100-240V 50/60Hz *This power supply is NOT designed to be used as a battery charger.
|
12V Bench Flashing Power Supply with Type G plug (UK, Malaysia & Singapore)
This 12V, 1.5A Power Supply (max output 13V) has been designed for use with Woolich Racing Bench Harnesses. This product comes with an integrated on/off switch and interchangeable Type G plug used in the UK, Ireland, Malaysia & Singapore. Input: 100-240V 50/60Hz *This power supply is NOT designed to be used as a battery charger.
|
Yamaha O2 Eliminator Type 1
The Woolich Racing O2 Eliminator allows you to remove the O2 Sensor/s from the motorcycle. The eliminator prevents the bike from displaying the Malfunction Indicator Light (MIL) on the dash and prevents fault codes from appearing in the diagnostic system. The eliminator should be plugged into the bikes wiring harness before the ignition is switched back on to prevent fault codes from being stored in the ECU. Supported models: - R1 2009-2014 - R6 2006-2016
|
Yamaha O2 Eliminator Type 1 (pack of 2)
The Woolich Racing O2 Eliminator allows you to remove the O2 Sensor/s from the motorcycle. The eliminator prevents the bike from displaying the Malfunction Indicator Light (MIL) on the dash and prevents fault codes from appearing in the diagnostic system. The eliminator should be plugged into the bikes wiring harness before the ignition is switched back on to prevent fault codes from being stored in the ECU. Supported models: - R1 2015-2020
|
|
|
Motorcycle Diagnostics - OBD2
|
|
Product
|
Description
|
Price
|
|
OBD2 Diagnostic Scanner (Advanced)
The OBD2 Diagnostic Scanner - Advanced allows you to read and clear fault codes when used in conjunction with the relevant Woolich Racing OBD2 Harness suitable to your bike.
Please note that not all OBD2 Diagnostic Scanners work on Motorcycles. This particular device has been tested by Woolich Racing and it works on the motorcycles where it is listed as a product.
|
Universal OBD2 Harness Type 1
This OBD2 harness allows you to connect to the 6 Pin Red Diagnostic Plug on the bike and read and clear fault codes using a OBD2 Diagnostic Scanner.
NOTE - This is the same harness as Kawasaki OBD2 Harness Type 4
This product is for customers who do not have access to one of our Interfaces but needs to read and clear fault codes. This product is not required if you already have a Woolich Racing Interface and On Bike Harness as we have diagnostics built into the software.
Note: OBD2 Diagnostic Scanner is not included, please see our listings for OBD2 Diagnostic Scanners that we have tested and work for this application.
Compatible with the following models:
Kawasaki Ninja 650/EX650 2020-2022 Kawasaki Z400 2023-2024 Kawasaki Z650 2020 Kawasaki Z900 RS 2020-2021 Kawasaki Ninja 400/EX400 2023 Kawasaki Z H2 2020-2023 Kawasaki ZX10R 2021-2023 Kawasaki ZX10RR 2021-2022 Kawasaki ZX-25R 2020-2022
Kawasaki Versys 1000 2021-2022 Kawasaki Z1000SX / Ninja 1000 2020-2022 Kawasaki ZX-4R / ZX-4RR 2023-2024 Kawasaki ZX6R (636) 2021-2024 Kawasaki Ninja 650 / EX650 2023 Kawasaki Z400 2023-2024 Kawasaki Z900 2023 Suzuki DL1050 V-Strom 2020-2022 Suzuki GSX1300R (Hayabusa) 2021-2023 Suzuki GSX-S 1000 2021-2023 Suzuki GSX-S 1000 GT 2021-2023 Yamaha MT-09 2021-2022 Yamaha MT-09 SP 2021-2022 Yamaha MT-09 Tracer 2021-2022 Yamaha MT-09 Tracer GT 2021-2022 Yamaha MT-10 2022-2023 Yamaha MT-10 SP 2022-2023 Yamaha XSR 900 2022-2023 Yamaha YZF-R1 2020-2022
|
Yamaha OBD2 Harness Type 1
This OBD2 harness allows you to connect to the 4 Pin YDS Diagnostic Plug on the bike and read and clear fault codes using a OBD2 Diagnostic Scanner.
This product is for customers who do not have access to one of our Interfaces but needs to read and clear fault codes. This product is not required if you already have a Woolich Racing Interface and On Bike Harness as we have diagnostics built into the software.
Note: OBD2 Diagnostic Scanner is not included, please see our listings for OBD2 Diagnostic Scanners that we have tested and work for this application.
Compatible with the following models:
Yamaha FJR1300 2016-2023 Yamaha FZ-09 2015 -2017 Yamaha MT-03 2018 -2021 Yamaha MT-09 2017-2020 Yamaha MT-09 SP 2018 -2020 Yamaha MT-10 2016-2021 Yamaha MT-10 SP 2017-2021 Yamaha Niken 2018-2020 Yamaha XSR 900 2016-2021 Yamaha YZF-R1 2017 -2019 Yamaha YZF-R25 2018-2019 Yamaha YZF-R3 2018 -2021 Yamaha YZF-R6 2017 -2020
|
OBD2 Diagnostic Scanner (Basic)
The OBD2 Diagnostic Scanner - Basic allows you to read and clear fault codes when used in conjunction with the relevant Woolich Racing OBD2 Harness suitable to your bike.
Please note that not all OBD2 Diagnostic Scanners work on Motorcycles. This particular device has been tested by Woolich Racing and it works on the motorcycles where it is listed as a product.
|
|
| Woolich Racing Merchandise |
|
Product
|
Description
|
Price
|
|
Woolich Racing Keytag
Woolich Racing embroidered keytag - easy to retrieve your keys even with bike gloves on!
|
|
| Wideband O2 Products |
|
Product
|
Description
|
Price
|
|
Zeitronix ZT-3 Wideband O2 Kit
Includes - Zeitronix ZT-3 Wideband O2 Controller
- 3 foot O2 sensor harness
- Extended primary O2 sensor harness (easier to fit to motorcycles)
|
Ducati Wideband O2 Installation Kit (Zeitronix) (type 3)
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 to a Ducati V2 motorcycle Includes: - 2 x Wideband O2 sensor bung
- 2 x 12v Automotive Relay
- 2 of each Red and Black 1.5mm Automotive Wire
- 8 * push on terminals
- 4 * 6mm eye connectors
- Heatshrink
- 2 x Wiretap
- RJ12 cable for connecting ZT-3 to Woolich Racing Products
- 2 x Adhesive Velcro for attaching ZT-3
|
Ducati Wideband O2 Installation Kit (Zeitronix) Type 1 (Stainless Steel)
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 to relevant Ducati models (Stainless Steel Bungs) Includes: - Twin RJ12 cable to connect Zeitronix to Log Box
- Short O2 sensor harness to ZT3
- Ducati Power Harness 1 & 2
- x O2 Stainless Steel Bung
- Adhesive Velcro for attaching ZT-3 to bike.
|
Ducati Wideband O2 Installation Kit (Zeitronix) Type 1 (Titanium)
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 to relevant Ducati models (TITANIUM Bungs)
Includes: - Twin RJ12 cable to connect Zeitronix to Log Box
- Short O2 sensor harness to ZT3
- Ducati Power Harness 1 & 2
- 2 x O2 TITANIUM Bungs
- Adhesive Velcro for attaching ZT-3 to bike.
|
Ducati Wideband O2 Installation Kit (Zeitronix) Type 2
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 to relevant Ducati models
Includes: - RJ12 cable for connecting ZT-3 to Woolich Racing Products
- Ducati Wideband Power Harness Type 3
- 1 x O2 Stainless Steel Bung
- Adhesive Velcro for attaching ZT-3 to bike.
|
Honda Wideband O2 Installation Kit (Zeitronix ZT3)
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 Kit to relevant Honda models.
Includes: - RJ12 cable for connecting ZT-3 to Woolich Racing Products
- Honda Wideband Power Harness Type 1
- 1 x O2 Stainless Steel Bung
- Adhesive Velcro for attaching ZT-3 to bike.
|
Kawasaki Wideband O2 Installation Kit (Zeitronix) (Type 1)
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 to relevant Kawasaki models
Includes: - RJ12 cable for connecting ZT-3 to Woolich Racing Products
- Kawasaki Power Harness Type 1
- O2 Stainless Steel Bung
- Adhesive Velcro for attaching ZT-3 to bike.
|
Kawasaki Wideband O2 Installation Kit (Zeitronix) (Type 2)
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 to relevant Kawasaki models
Includes: - RJ12 cable for connecting ZT-3 to Woolich Racing Products
- Kawasaki Power Harnes Type 2
- O2 Stainless Steel Bung
- Adhesive Velcro for attaching ZT-3 to bike.
|
KTM Wideband O2 Installation Kit (Zeitronix ZT4)
Installation kit for fitting the Zeitronix ZT-4 Dual Wideband O2 Kit to relevant KTM models
Includes: - RJ12 cables for connecting ZT-3 to Woolich Racing Products
- KTM Power Harness Type 1
- 2 x O2 Stainless Steel Bung
- Adhesive Velcro for attaching ZT-4 to bike.
|
Suzuki Wideband O2 Installation Kit (Zeitronix)
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 to relevant Suzuki models
Includes: - RJ12 cable for connecting ZT-3 to Woolich Racing Products
- Suzuki Power Harness
- O2 Stainless Steel Bung
- Adhesive Velcro for attaching ZT-3 to bike.
|
Woolich Racing Tuning Shop Zeitronix Installation Kit
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 to a motorcycle Includes: - Wideband O2 sensor bung (stainless Steel)
- Wideband O2 sensor bung (Titanium)
- Tuning Shop Power Harness (type 1)
- RJ12 cables for connecting ZT-3 to Woolich Racing Products - 1 x small, 1 x large
- 2 x Narrow band bungs
|
Woolich Racing Zeitronix Installation Kit
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 to a motorcycle Includes: - Wideband O2 sensor bung
- 12v Automotive Relay
- Red and Black 1.5mm Automotive Wire
- 4 * push on terminals
- 2 * 6mm eye connectors
- Heatshrink
- Wiretap
- RJ12 cable for connecting ZT-3 to Woolich Racing Products
- Adhesive Velcro for attaching ZT-3 to bike.
|
Woolich Racing Zeitronix Installation Kit ZT-3 OBD2
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 for motorcycles that use the red OBD plug. Includes: - Wideband O2 sensor bung
- OBD2 Wideband Harness Type 1
- RJ12 cable for connecting ZT-3 to Woolich Racing Products
- Adhesive Velcro for attaching ZT-3 to bike.
|
Woolich Racing Zeitronix Installation Kit ZT-4 OBD2
Installation kit for fitting the Zeitronix ZT-4 Wideband O2 for motorcycles that use the red OBD plug. Includes: - Wideband O2 sensor bung
- OBD2 Wideband Harness Type 2
- RJ12 cable for connecting ZT-4 to Woolich Racing Products
- Adhesive Velcro for attaching ZT-4 to bike.
|
Woolich Racing Zeitronix Installation Kit (ZT-4)
Installation kit for fitting the Zeitronix ZT-4 Dual Wideband O2 to a motorcycle Includes: - 2 x Wideband O2 sensor bungs
- Wideband Harness (to connect battery terminal for power)
- RJ12 cable for connecting ZT-4 to Woolich Racing Products
- Adhesive Velcro for attaching ZT-4 to bike.
|
Yamaha Wideband O2 Installation Kit (Zeitronix)
Installation kit for fitting the Zeitronix ZT-3 Wideband O2 to relevant Yamaha models
Includes: - RJ12 cable for connecting ZT-3 to Woolich Racing Products
- Yamaha Power Harness
- O2 Stainless Steel Bung
- Adhesive Velcro for attaching ZT-3 to bike.
|
Zeitronix ZT-4 Dual Wideband O2 Kit
Zeitronix ZT-4 Dual Wideband O2 Controller Kit, with 2 x Zeitronix Wideband O2 Sensor (3 foot cable)
Woolich Racing - Tuning Shop Zeitronix Power Harness Type 3 1 x RJ12 Cable
|
Stainless Steel Wideband O2 Bung
High Quality 18mm Stainless Steel Wideband O2 Bung. You can weld this bung into exhaust systems that do not have a Wideband O2 bung.
|
Titanium Wideband O2 Bung
High Quality 18mm Titanium Wideband O2 Bung. You can weld this bung into exhaust systems that do not have a Wideband O2 bung.
|
Wideband Bung Bolt
The Stainless Steel Wideband Bung Bolt allows you to block off a Wideband O2 bung when the Wideband O2 sensor is not installed.
|
Wideband Bung Bolt Race
The Stainless Steel Wideband Bung Bolt allows you to block off a Wideband O2 bung when the Wideband O2 sensor is not installed. This Race version of the bung bolt is light weight and has holes pre-drilled for lock wiring.
|
Narrowband Bung Bolt
The Stainless Steel 12mm Narrowband Bung Bolt allows you to block off a Narrowband O2 bung allowing the Narrowband sensor to be entirely removed from the bike.
|
Narrowband to Wideband O2 Adapter
The Narrowband to Wideband O2 sensor adapter screws into a 12mm Narrowband bung, allowing you to use a Wideband O2 sensor with a Narrowband bung.
Please Note: This is a generic item and may not fit all makes/models due to potential clearance issues that arise from the manufacturers' designs. Please ensure you have adequate clearance for the adapter -AND- the O2 sensor when installed in the factory narrowband location.
- O2 Adapter Height: Approximately 32 mm extending vertically when installed in the stock narrowband location. - O2 Sensor Height: Plan for at least 70 mm of additional height on top of the O2 Adapter when the wideband O2 sensor is installed.
For models where clearance could be an issue, it is suggested to use the wideband bung included in the Zeitronix installation kit or find an alternative narrowband to wideband adapter such as the Innovate 12mm to 18mm O2 BUNG ADAPTER, P/N 38350 which angles the sensor to help potentially alleviate any clearance issues.
|
Zeitronix ZR-1 AFR Gauge Blue LED
- Stylish, machined, anodized black bezel and slim enclosure
- High contrast Blue LED display
- Large 0.4" (10mm) digits
- Slim design for flexible gauge mounting options
- Programmable to startup as an AFR or Lambda gauge
- Peak and Hold feature
- RJ12 Splitter cable included
|
Zeitronix ZR-1 AFR Gauge Red LED
- Stylish, machined, anodized black bezel and slim enclosure
- High contrast Red LED display
- Large 0.4" (10mm) digits
- Slim design for flexible gauge mounting options
- Programmable to startup as an AFR or Lambda gauge
- Peak and Hold feature
- RJ12 Splitter cable included
|
Zeitronix ZR-3 AFR Gauge Blue LED
- Blue digital AFR readout with large 0.4" (10mm) digits
- Slim 0.75" (19mm) design
- High contrast display visible even in direct sunlight
- RJ12 Splitter cable included
|
Zeitronix ZR-3 AFR Gauge Red LED
- Red digital AFR readout with large 0.4" (10mm) digits
- Slim 0.75" (19mm) design
- High contrast display visible even in direct sunlight
- RJ12 Splitter cable included
|
Hacker/Tweaker AFR Display Blue LED
The Zeitronix Hacker/Tweaker is a very small AFR or Lambda display for the Zt-3 Wideband Systems. Designed to fit into tight spots, full board dimensions are less than 2" by 1". Like all LED displays it requires a tinted foil or Lexan cover. There are two mounting holes for screws or standoffs. It powers up right from the Zt-3 DATA port. RJ12 splitter cable included.
Note: The Hacker/Tweaker is a bare PCB board, you will need to make your own case.
|
Hacker/Tweaker AFR Display Red LED
The Zeitronix Hacker/Tweaker is a very small AFR or Lambda display for the Zt-3 Wideband Systems. Designed to fit into tight spots, full board dimensions are less than 2" by 1". Like all LED displays it requires a tinted foil or Lexan cover. There are two mounting holes for screws or standoffs. It powers up right from the Zt-3 DATA port. RJ12 splitter cable included.
Note: The Hacker/Tweaker is a bare PCB board, you will need to make your own case.
|
|
| |
|
|
|
|